MFD12 AND SOUNDER ETR 6/10

MFD12 AND SOUNDER ETR 6/10

Postby leccese3 » Thu Jun 29, 2017 5:55 am

HI THERE EVERYBODY

JUST BOUGHT MFD12 NAVNET 3D CHARTPLOTER, CONNECTED THE ANTENNA GOT IT I HAVE GPS POSITION AND TIME, CONNECTED THE SOUNDER WITH MFD12 AND NO SIGNAL ??

MFD12 SOFTWARE VERSION IS: 1950055-02.11
MFD12 IS SET AS MASTER

WHAT I SHOULD TEST OR CHECK SO I CAN SEE SOUNDER DETECTED BY THE MFD12

WAITING YOUR KIND HELP

BEST REGARDS
leccese3
Member
Member
 
Posts: 7
Joined: Thu Jun 29, 2017 5:43 am


Re: MFD12 AND SOUNDER ETR 6/10

Postby Melville » Fri Jun 30, 2017 9:06 am

If you run through the installation wizard you should see it.
Once done with the procedure there will be a sounder icon in the upper right corner and sounder will also be listed in the menu.
Melville
Furuno USA
User avatar
Melville
Moderator
Moderator
 
Posts: 808
Joined: Fri Sep 02, 2011 12:33 pm

Re: MFD12 AND SOUNDER ETR 6/10

Postby leccese3 » Sun Jul 02, 2017 6:29 pm

Thanks for the replay,

I run the wizard and nothing show up,
The sounder icon does not shows on the screeen.

Green light in the furuno etr-6/10 is on .
Do i have to activate an option on the mdf12 to turn on the ethernet ??

Waiting for your help ??
leccese3
Member
Member
 
Posts: 7
Joined: Thu Jun 29, 2017 5:43 am

Re: MFD12 AND SOUNDER ETR 6/10

Postby Johnny Electron » Mon Jul 03, 2017 7:05 am

After power up the system, wait five minutes and check the sounder status light. What is it doing? Is it solid, flashing quickly, flashing slowly at a one second "On"/ one second "off" ?
Johnny Electron
User avatar
Johnny Electron
Moderator
Moderator
 
Posts: 3291
Joined: Tue Sep 06, 2011 4:26 am
Location: USA

Re: MFD12 AND SOUNDER ETR 6/10

Postby leccese3 » Sun Jul 09, 2017 8:44 am

Helllo there capitán

I went to the boat and turn everything on,
The etr6/10n starts with a flashing check and then stays solid.
The blue round 6 pin ethernet cable from the etr6/10n has a convertion cable to fit
The navnet 3d back etherneth switch.

As far as i hace read this old sounder model etr6/10n has a net name , net #, net submask, etc
This un order to be detected by displays and to transmit info ??

Waiting for your kind advice and comments

Regardss, Ettore
leccese3
Member
Member
 
Posts: 7
Joined: Thu Jun 29, 2017 5:43 am

Re: MFD12 AND SOUNDER ETR 6/10

Postby Johnny Electron » Tue Jul 11, 2017 5:53 am

If the status light goes solid after 4 mins; then you have a communications error. Your cabling or hub connection should be checked. The sounder seems to be working okay at this point.
Johnny Electron
User avatar
Johnny Electron
Moderator
Moderator
 
Posts: 3291
Joined: Tue Sep 06, 2011 4:26 am
Location: USA


Return to NavNet 3D

Who is online

Users browsing this forum: No registered users and 2 guests